0531-6667 8888
公司新闻
Company news
按钮开关型号|正确的安装方式和使用技巧
作者: 时间:2020-09-24 14:16 阅读数:

  正确的安装方式是按钮开关发挥功能的关键所在,在安装按钮开关时要多加注意,根据安装说明,一步一步的进行安装,避免因急于求成而安装错误,导致按钮开关无法正常工作。正确安装按钮开关的方式如下:

  The correct installation method is the key to the function of the button switch. More attention should be paid to the installation of the button switch. According to the installation instructions, the button switch should be installed step by step, so as to avoid the installation error caused by being too eager for success, resulting in the button switch unable to work normally. The correct way to install the button switch is as follows:

  1、将按钮安装在面板上时,要求布置整齐,排列合理,根据电动机启动的先后次序,从上到下或从左到右排列。

  1. When the buttons are installed on the panel, they are required to be arranged orderly and arranged reasonably. According to the sequence of motor starting, they should be arranged from top to bottom or from left to right.

  2、按钮的安装应固定牢固,接线可靠。在按钮颜色的应用上,用红色按钮表示停止,绿色或黑色表示启动或通电。

  2. The installation of the button should be fixed firmly and the wiring should be reliable. The green color of the start or stop button is indicated by the red color on the power on button.

  3、安装按钮的按钮板与按钮盒必须是金属的,设法使它们与机床总接地母线相连接,悬挂式按钮必须设有专用接地线,禁止借用金属管作为地线。

  3. The button board and the button box for installing the button must be metal. Try to connect them with the general grounding bus of the machine tool. The hanging button must be equipped with special grounding wire. It is forbidden to borrow metal tube as the ground wire.

按钮开关

  按钮开关的使用技巧

  Using skills of button switch

  1、按钮触头间距离较小,如有油污等容易发生短路故障,需要保持触头的清洁。

  1. The distance between the contacts of the button is small, if there is oil pollution, it is easy to cause short circuit fault, so it is necessary to keep the contact clean.

  2、按钮开关用于高温场合时,易使塑料变形老化而导致松动,引起接线螺钉间相碰短路,可在接线螺钉处加套绝缘塑料管来防止短路。

  2. When the button is used in high temperature situation, it is easy to make the plastic deformation and aging, resulting in loosening, causing the contact short circuit between the connecting screws. An insulating plastic pipe can be added at the connection screw to prevent short circuit.

  3、带指示灯的按钮开关因灯泡发热,长期使用易使塑料灯罩变形,应降低灯泡电压,延长使用寿命。

  3. The button with indicator lamp is easy to deform the plastic lampshade due to the bulb heating. The bulb voltage should be reduced and the service life should be extended.

  4、“停止”按钮必须是红色;“急停”按钮必须是红色蘑菇头式;“启动”按钮必须有防护挡圈,防护挡圈应高于按钮头,以防意外触动使电气设备误动作。

  4. "Stop" button must be red; "emergency stop" button must be red mushroom head type; "start" button must be equipped with a protective ring, which should be higher than the button head, so as to prevent accidental touch and misoperation of electrical equipment。