0531-6667 8888
公司新闻
Company news
分离式结构的按钮开关正确的安装顺序
作者: 时间:2020-09-18 16:16 阅读数:

  按钮开关一般是使用于电力、化工、军工、纤维、炼油、纺织、石油开采等领域的生产机器上,可以说应用范围非常广泛。当然,按钮开关的使用方法是非常简单的,一键开启,一键关闭,非常方便。但其具体的安装方法以及注意事项,你都知道吗?

  Button switch is generally used in electric power, chemical industry, military industry, fiber, oil refining, textile, oil mining and other fields of production machinery, it can be said that the application range is very wide. Of course, the use of button switch is very simple, one button to open, one button to close, very convenient. But do you know the specific installation method and precautions?

  现在市面上的按钮开关基本上都是以分离式结构为主,一般分为装饰帽、紧固圈、活动卡扣、触点系统、接线螺丝五个部分,虽然从其结构看起来较为复杂,但安装还是比较简单的。

  At present, the push-button switch on the market is basically separated structure, which is generally divided into five parts: decorative cap, fastening ring, movable buckle, contact system and wiring screw. Although the structure seems more complicated, the installation is relatively simple.

  首先是先将纽罩起子打开,将螺母扭下;其次,将打开的开关下部套入面板孔中;接下来,将钮罩嵌入。

  First, open the button cover driver and screw down the nut; secondly, insert the lower part of the opened switch into the panel hole; next, insert the button cover.

  按钮开关的在安装过程中的注意事项:先将按钮安装到面板上,并将其布置整齐、排列合理,这样才方便记忆辨认不同按钮开关的作用;如果要在同一设备上安装多个按钮开关的话,一定要将每对相反状态的按钮开关安装到一起,比如将代表停止的红色按钮开关与代表启动的其它颜色开关安装到一起,这样才能在很大程度上避免按错。

  Precautions in the installation process of button switch: first install the button on the panel, and arrange it orderly and reasonably, so as to facilitate the memory and identification of the functions of different button switches; if multiple button switches are to be installed on the same equipment, each pair of button switches in the opposite state must be installed together, such as the red button switch representing the stop and the red button switch representing the stop Other color switches representing start-up are installed together, so as to avoid mispressing to a great extent.

按钮开关型号

  另外,有时机器会出现紧急情况,所以需要安装一个总停按钮,而总停按钮应该安装在最显眼的地方,而且可以在按钮开关上做个明显的标记,这样才能在紧急情况时,及时暂停机器生产;当然,按钮开关是需要经常清洁的,避免灰尘、油污对其造成短路故障。

  In addition, sometimes the machine will have an emergency, so it is necessary to install a general stop button, and the general stop button should be installed in the most conspicuous place, and an obvious mark can be made on the button switch, so as to stop the production of the machine in time in case of emergency; of course, the button switch needs to be cleaned regularly to avoid short circuit fault caused by dust and oil pollution.

  安装按钮开关的按钮盒和按钮板必须是金属制的,并让其与机床总接地母线相连,不过对于悬挂式按钮必须设有专用接地线,不能借用金属管作为地线,这样才能导电。

  The button box and button board for installing the button switch must be made of metal and connected with the general grounding bus of the machine tool. However, for the hanging button, special grounding wire must be set, and metal tube can not be used as the ground wire, so as to conduct electricity.

  另外,某些按钮开关内的指示灯,其长期使用会发热,从而导致塑料灯罩变形,所以应降低指示灯电压,来延长使用寿命。

  In addition, some indicator lights in the button switch will be heated for a long time, which will cause deformation of the plastic lampshade. Therefore, the voltage of the indicator lamp should be reduced to prolong its service life